[Nov-2023] ASQ CQE Exam: Basic Questions With Answers

New 2023 Realistic Free ASQ CQE Exam Dump Questions and Answer

NEW QUESTION # 29
The use of 100% inspection normally means

• A. That there will be an opportunity to rework any product deemed to be outside of specifications.
• B. That selected characteristics have been evaluated against specified standards.
• C. That the lowest over-all quality costs have been considered.
• D. That the final customers will not experience defective product.

Answer: B

NEW QUESTION # 30
Which of the following quality system provisions is of the greatest concern when preparing an audit checklist for a vendor qualification system audit?

• A. Makeup of the MRB
• B. Training level of inspectors.
• C. Drawing and print control.
• D. Calibration of test equipment.

Answer: D

NEW QUESTION # 31
For TQM success, what structure sequence should be followed?
I. Develop a quality policy.
II. Establish a quality council.
III. Establish strategic quality goals.
IV. Train for internal audits.

• A. II, III, I, IV
• B. I, II, III, IV
• C. II, I, III, IV
• D. III, II, I, IV

Answer: C

NEW QUESTION # 32
Which of the following is the BEST statement to make regarding the relationship between product precision and product production?

• A. With little precision, performance will improve.
• B. With too little precision, production costs increase.
• C. With too much precision, production costs increase.
• D. Precision costs and performance are related.

Answer: D

NEW QUESTION # 33
Regardless of the distribution of the individuals, the distribution of the average of n samples will follow which distribution as n becomes large?

• A. Exponential.
• B. Normal
• C. Poisson.
• D. Lognormal.

Answer: B

NEW QUESTION # 34
The power of efficiency in designed experiments lies in the

• A. Random order of performance.
• B. The large number of possible combinations of factors.
• C. The sequential and cyclical procedure of conjecture to design to analysis and back to conjecture.
• D. Hidden replication.

Answer: D

NEW QUESTION # 35
A system was designed with 3 capacitors. When the system is first activated all capacitors are operating. The system continues to operate as long as at least 1 capacitor is operating. This is an example of

• A. An active parallel system.
• B. A series system.
• C. Redundancy.
• D. A standby parallel system.

Answer: A

NEW QUESTION # 36
A lot is known to be 1.2% defective. Five units are randomly selected from the lot, and the lot is accepted if 1 or fewer defects are found. What is the probability of the lot being rejected?

• A. 0.9985
• B. 0.00223
• C. 0.01
• D. 0.00173

Answer: D

Explanation:
Explanation/Reference:

NEW QUESTION # 37
The following measurements for a sample with dimension X are representative of a process known to be in statistical control
42, 52, 64, 45, 53, 56, 70, 57, 49, 62
Which of the following values BEST approximates the upper and lower control limits of the process capability.

• A. 81 and 29
• B. 70 and 42
• C. 64 and 46
• D. 59 and 51

Answer: A

NEW QUESTION # 38
A typical use for the optical comparator would be to measure

• A. Depth of holes.
• B. Contours.
• C. Diameters of internal grooves.
• D. Surface finish.

Answer: B

NEW QUESTION # 39
Which of the following is a valid null hypothesis?

• A. The mean of population A is not equal to the mean of population B
• B. p > 1/8
• C. μ < 98
• D. mu = 110

Answer: D

NEW QUESTION # 40
A process is turning out end items that have defects of type A or type B or both. If the probability of type A defect is 0.1 and of a type B is 0.2, the probability that an end item will have no defect is

• A. 0.30
• B. 0.7
• C. 0.72
• D. 0.68

Answer: C

NEW QUESTION # 41
Which of the following statements BEST describes a bimodal distribution?

• A. This distribution is truncated.
• B. This distribution has several distribution peaks.
• C. This distribution shows a single mode and bell shaped distribution.
• D. This distribution shows stratified data and two distinct peaks.

Answer: D

NEW QUESTION # 42
A quality control program is considered to be

• A. A collection of quality control procedures and guidelines.
• B. A summary of company quality control policies.
• C. A system of activities to provide quality of products and service.
• D. A step by step listing of all quality control check points.

Answer: C

NEW QUESTION # 43
The weight of paint cans is considered

• A. Probability data.
• B. Random data.
• C. Discrete data.
• D. Continuous data.

Answer: D

NEW QUESTION # 44
Maintainability is

• A. Maintaining a machine in satisfactory working condition.
• B. Probability of survival of a system for a given period of time.
• C. The probability of a system being restored to functional operation within a given period of time.
• D. Performing adequate maintenance on a system.

Answer: C

NEW QUESTION # 45
When asked to make recommendations on how to correct any deficiencies noted in the exit report, the auditor(s) should

• A. Confer with the client first.
• B. Make the best recommendation possible.
• C. Offer no specific advice and few suggestions.
• D. Avoid a recommendation in writing but help the auditee of possible.

Answer: C

NEW QUESTION # 46
Which of the following distributions have the set of all real numbers as their domain?

• A. Weibull
• B. Lognormal
• C. None of the above.
• D. Exponential

Answer: C

NEW QUESTION # 47
......

Guaranteed Success in ASQ Certification CQE Exam Dumps: https://passguide.braindumpsit.com/CQE-latest-dumps.html